item
Linear Unit GSF 8 40 R10

Linear Unit GSF 8 40 R10

0.0.655.98

1 3.860
On request
configure now
* Mandatory information

Technical Data

item products are based on different modular dimensions and their associated system grooves.Profiles from Lines 5, 6, 8, 10 and 12 each need corresponding sizes of fasteners.The profiles in Line X feature a Line 8 system groove but have a particularly flat surface withminimum curve radii that make them ideal for building sealed constructions.
All substances are registered according to the REACH regulation.REACH (Registration, Evaluation, Authorisation and Restriction of Chemicals) ensures that usershave accurate information on the type and properties of operating materials, lubricants, etc.that they might come into contact with.
Components that are RoHS-compliant contain no dangerous substances such as lead or cadmium.EC Directive 2002/95/EC (RoHS 1) restricts the use of certain substances in electronic devices and components.These include batteries, etc.

Properties

Article number 0.0.655.98
Line line 8
ESD-safe No
Moment of Inertia, torsional It = 2,71 cm4
Moment of Inertia, x-axis Ix = 9,75 cm4
Moment of Inertia, y-axis Iy = 9,48 cm4
Total mass m = m1 + H * m2
Maximum operating load Fx max = 150 N
Maximum force in direction y Fy max = 25 N
Maximum force in direction z Fz max = 50 N
Weight m = 1,165 kg
Weight m = 1,846 g/mm
Weight m = 1,846 kg/m
Weight per length of the drive medium (timing belt, chain) mlz = 0,023 kg/m
Efficiency . = 1
Delivery unit 1 pce.
Basic mass (when stroke length = 0 mm) m1 = 1,165 kg
Mass per mm of stroke m2 = 1,846 g/mm
Max. acceleration amax  = 3 m/s2
Max. speed Vmax = 1 m/s
Repeat accuracy . = 0.5 mm
Mass moment of inertia when stroke length = 0 mm J0 = 67 kg mm2
Mass moment of inertia per kg of payload JN = 335 kg mm2/kg
Mass moment of inertia per m of stroke JH = 13,1 kg mm2/m
Stroke max. Hmax = 3.860 mm
max. drive torque . = 3 Nm
Maximum moment around the x axis Mx max = 0,4 Nm
Maximum moment around the y axis My max = 2 Nm
Maximum moment around the z axis Mz max = 1,25 Nm
Frictional moment . = 0,1 Nm
Safety clearance smin = 27,5 mm
Support width when Fy max. .  = 2.400 mm
Support width when Fz max. .  = 2.100 mm
Stroke h = 115 mm/r
Resistance Moment, x-axis Wx = 4,83 cm3
Resistance Moment, y-axis Wy = 4,74 cm3

Description

Light, quiet and high-performance! Linear Unit GSF 8 40 R10 is an efficient turnkey system with minimal space requirements. This economic Linear Unit uses only a few components to deliver maximum performance. For example, the slide uses a Line 8 groove on the support profile as its guide. It runs without lubricants on a wear-resistant sliding shoe.
The Drive Unit and Reverse Unit feature an exceptionally compact design. The tensioning device for the Timing Belt is integrated into the Reverse Unit. Its ball-bearing mounted pulleys ensure quiet and smooth running over long-term use. The Timing Belt is routed back through the profile groove.
The compact dimensions and maintenance-free design make Linear Unit GSF 8 40 R10 an exceptionally efficient solution. It is ideal for applications that require the movement of low loads. Thanks to the practical hollow shaft, an expanding hub coupling can be installed on the right or left, as appropriate to the installation.
Note: Linear Unit GSF 8 40 R10 is supplied ready for installation as a turnkey system in the desired stroke length. The components can also be ordered separately and assembled to form customised units.
Load specifications
Run length under max. load: 1000 km
Max. speed: 1 m/s
Due to their construction, slide guides can exhibit slight irregularities (stick/slip effect) when running at low speeds and under increased loads. This effect can be magnified when the Timing Belt is subject to excessive tension. Linear Unit GSF is recommended for use in applications that involve vertical loads.
Travel speed v in relation to input speed n (timing-belt drive)
Operational force Fx dependent on input torque M (timing-belt drives Fx ≤ 500N)

Load Calculation

Downloads

CAD Data

Classification

Classifications are industry-wide product data standards that are used, among other things, to support structured processing in ERP and e-business systems. Do you need the classification data for all item products for your e-procurement system? If so, please don’t hesitate to contact us.
eCl@ss 8.0
23301702
eCl@ss 4.0
36400806
eCl@ss 7.1
23301702
eCl@ss 4.1
36400701
eCl@ss 5.0
23329090
eCl@ss 5.1
23329090
eCl@ss 6.0.1
23301702
eCl@ss 11.0
23301702
UNSPSC 7.0
26111506
UNSPSC 9.0
26111506
Customs tariff number
84879090