item
Linear Unit KLE

Linear Unit KLE


Show all 3 variants
1 5.750
On request
configure now
* Mandatory information

Technical Data

item products are based on different modular dimensions and their associated system grooves.Profiles from Lines 5, 6, 8, 10 and 12 each need corresponding sizes of fasteners.The profiles in Line X feature a Line 8 system groove but have a particularly flat surface withminimum curve radii that make them ideal for building sealed constructions.
All substances are registered according to the REACH regulation.REACH (Registration, Evaluation, Authorisation and Restriction of Chemicals) ensures that usershave accurate information on the type and properties of operating materials, lubricants, etc.that they might come into contact with.
Components that are RoHS-compliant contain no dangerous substances such as lead or cadmium.EC Directive 2002/95/EC (RoHS 1) restricts the use of certain substances in electronic devices and components.These include batteries, etc.

Properties

Article number 0.0.605.07
Line line 6
ESD-safe No
Moment of Inertia, torsional It = 6,64 cm4
Moment of Inertia, x-axis Ix = 44,49 cm4
Moment of Inertia, y-axis Iy = 57,11 cm4
Total mass m = m1 + H * m2
Maximum operating load Fx max = 500 N
Maximum force in direction y Fy max = 750 N
Maximum force in direction z Fz max = 500 N
Weight m = 4,074 kg
Weight m = 4,889 g/mm
Weight m = 4,889 kg/m
Weight per length of the drive medium (timing belt, chain) mlz = 0,082 kg/m
Efficiency . = 1
Delivery unit 1 pce.
Basic mass (when stroke length = 0 mm) m1 = 4,074 kg
Mass per mm of stroke m2 = 4,889 g/mm
Max. acceleration amax  = 10 m/s2
Max. speed Vmax = 10 m/s
Repeat accuracy . = 0.1 mm
Mass moment of inertia when stroke length = 0 mm J0 = 705 kg mm2
Mass moment of inertia per kg of payload JN = 608,6 kg mm2/kg
Mass moment of inertia per m of stroke JH = 100 kg mm2/m
Stroke max. Hmax = 5.750 mm
max. drive torque . = 12 Nm
Maximum moment around the x axis Mx max = 20 Nm
Maximum moment around the y axis My max = 50 Nm
Maximum moment around the z axis Mz max = 75 Nm
Frictional moment . = 1 Nm
Safety clearance smin = 26 mm
Support width when Fy max. .  = 1.500 mm
Support width when Fz max. .  = 1.600 mm
Stroke h = 155 mm/r
Resistance Moment, x-axis Wx = 13,11 cm3
Resistance Moment, y-axis Wy = 19,04 cm3

Description

In the compact KLE linear units, the rollers run inside the profile. Apart from the slide, no moving parts can be touched because the timing belt in the guide groove covers the moving elements. This increases occupational safety and reduces soiling of guides and rollers.

KLE linear units are supplied ready for installation with a stroke length of up to 5750 mm. They are available in lines 6 and 8 with corresponding grooves on the outside. With an overall width of just 60 mm including the slide, the KLE 6 linear unit is one of the narrowest linear units with roller guides.

The special aluminium support profile ensures high load-bearing capacity and low-vibration operation. Thanks to their smooth running and resilient drive elements, KLE linear units are particularly suitable for positioning tasks with high travel speeds.

The guide carriage runs on four rollers and two hardened guide shafts within the profile. A carriage plate KLE or compound slide plate KLE is used to connect applications. The timing belt tensioning device is integrated into the deflection.

The KLE 8 linear unit has been tested for cleanroom suitability up to ISO class 6 in accordance with ISO 14644-1.
Simplified method for determining the maximum permissible load for the Roller Guides of a KLE:
The maximum deflection fmax of the system is governed by the dimension of the profile cross-section, the free profile length and the force applied.
It should not exceed 1mm/m.
The KLE profile must be given appropriate support if the linearity of movement has to be very precise.
The carriage plate of the KLE 6 60x60 has two drilled holes used to pin the carriage plate to the cover plate on the carriage. The carriage plate and cover plate need to be pinned so that they can accommodate the relevant forces and ensure they are reliably transmitted to the roller guide.
Two ø4H7 pinning holes are provided in the KLE 6 60x60 cover plate for this purpose.
It is advisable to use the dowel pins supplied with the carriage set in combination with the carriage plates.
KLE 6 60x60: Dowel Pin ISO 2338 4h8x30
KLE 8 80x80: Dowel Pin ISO 2338 6h8x40
If not using the original carriage plates, the pattern of holes must be copied from the drawings and transferred onto the custom carriage constructions.
h = horizontal orientation
v = vertical orientation
Maximum possible acceleration in relation to moved mass and installation orientation
Travel speed v in relation to input speed n (timing-belt drive)
Operational force Fx dependent on input torque M (timing-belt drives Fx ≤ 500N)

Variants

Sort by

Baureihe:  5 Hublänge:  1 ... 2800 Führungsart:  Welle D6 Zahnriemenbreite:  16 mm
Baureihe:  6 Hublänge:  1 ... 5750 Führungsart:  Welle D10 Zahnriemenbreite:  25 mm
Baureihe:  8 Hublänge:  1 ... 5600 Führungsart:  Welle D14 Zahnriemenbreite:  34 mm

Load Calculation

Downloads

Accessoires

Classification

Classifications are industry-wide product data standards that are used, among other things, to support structured processing in ERP and e-business systems. Do you need the classification data for all item products for your e-procurement system? If so, please don’t hesitate to contact us.
eCl@ss 8.0
23301702
eCl@ss 7.1
23301702
UNSPSC 7.0
26111506
UNSPSC 9.0
26111506
eCl@ss 4.1
36400701
eCl@ss 5.0
23329090
eCl@ss 5.1
23329090
eCl@ss 6.0.1
23301702
eCl@ss 11.0
23301702
eCl@ss 4.0
36400806
Customs tariff number
84879090